About this product
- Custom sized director's chair covers for any size chair with round or flat stick attachment
- 100% Made in the USA and sewn here in house to the measurements provided
- Made from Sunbrella® acrylic marine grade fabric that will not stretch, fade or shrink
- The same fabric used to make sails and in maritime furnishings
- Comes with the seat, back, and sticks if chosen.
Selectable Sunbrella® colors are the stock colors. All other colors available by special order only for an additional $30. There is a 2 cover set minimum for all special orders. Please call to special order 828-678-9660.
Breathe new life into old chairs! We now offer a custom sewing service to create Director Chair covers to your dimensions. Fabric is top quality Sunbrella® marine grade acrylic material. Sunbrella® is widely used for awnings, marine and outdoor furnishings. Director's chair covers are easy to replace and almost all require no additional hardware in order to replace them. Please read this Buying Guide article on how to Purchase and Install Directors Chair Covers.
Personalization - Personalization in the form of Imprinting and Embroidery can be added to the custom sized covers. It is not offered online due to the amount of information already required for our custom sized covers. Reach out to us directly at 828-678-9660 or mail@ewchair.com before placing your order and we will be glad to assist with this.
Be sure to measure carefully when submitting measurements. You must attest that the measurements are correct as submitted and NO returns are accepted for correctly sewn covers:
NOTE: Our custom sewing service only offers the sewn material. Customer is responsible for any cut outs that need to be made in the covers and for installation of any option hardware ie. grommets, bolts, rings, etc.
The Seat Dimensions are measured from EDGE to EDGE. WIDTH is from side to side on the chair where the sticks are. DEPTH is from front to back. SEAT LOOPS will be sewn to fit the stick sizes indicated below, unless otherwise indicated. The LOOPS are Measured from EDGE to the first SEW LINE and are included as part of the width. The seat loop measurement we need is the width of the pocket that the stick that secures the seat to the chair slides in. For example, our stock round stick covers take 1/4 inch diameter round dowels which require a seat loop measurement of 3/4 inches and our stock size flat stick covers take 1/4 inch x 9/16 inch flat sticks that require a 1 inch seat loop measurement.
The Back Dimensions are measured EDGE to EDGE also. WIDTH is from side to side on the chair with the loops flattened out. HEIGHT is from top to bottom parallel with the seat posts. BACK LOOPS are measured from the EDGE to the first SEW LINE and are included in with the width measurement. The back loop measurement we need is the width of the pocket that the back posts of the chair go through. Please DO NOT provide the diameter of the back post as this measurement. If the loop is made to that size, the back post will never slide through it. The most common seen back post diameter is 1 inch and this size requires a BACK LOOP measurement of 2.5 inches.
Oversize Charge: There will be a Oversize Charge PER DIMENSION if:
- Back Height is greater than 8"
- Seat Width is greater than 21"
- Seat Depth is greater than 16"
- Seat Loops are greater than 1.5"
- We will notify you of any incorrectly chosen Oversize Charge via email or phone
Choosing the Correct Oversize Option: When making the choice on the oversize options, it is important to know which option to choose. Take the Seat Width as an example. The options are 21 or Less, Between 21 - 25, and 25 or Greater. If the entered measurement is 21, the correct option would be "21 or Less" because numerically 21 is not "Between 21 - 25". If the entered measurement is 25, the correct option would be "25 or Greater" for the same reason. The only exception to this rule is the Back Height measurement. If the entered number is 10, choose the option "Between 8 - 10".
Seat Sticks: Round sticks are 1/4" in diameter, Flat sticks measure 1/4" x 9/16". Two sticks will be included if the option to include sticks is chosen.
If a current cover set is available for measuring, CLICK HERE for video instructions on how to obtain those measurements. If no covers are available and there is only a frame for measuring, CLICK HERE for video instructions on how to get the cover measurements from just the frame. Some chairs may be a little different (stick slots being on the under side of the frame) but the same principle for measuring illustrated in the video will also apply to those chairs.
NOTE: If you choose "Yes" to "Do you need sticks included?" we will make the seat loops to fit our sticks. If you are ordering Round Sticks, we will make the seat loops at 3/4". If you are ordering Flat Sticks, we will make the seat loops at 1"
For more information regarding the different parts of a cover set and how to obtain measurements, check out our blog Making Sense Out of Director's Chair Covers.
Measure carefully to make sure the replacement sling fits your chair. Call us at 1-828-678-9660 if you need assistance.
